2456200000 ACT20X-HUI-SAO-P
Brand: Weidmüller
Code: 2456200000
EX signal isolating converter, Ex-output: U, I, R,ϑ, Safe-output: 4-20mA/ relay, 1-channel
| Version | EX signal isolating converter, Ex-output: U, I, R,ϑ, Safe-output: 4-20mA/ relay, 1-channel |
| Order No. | 2456200000 |
| Type | ACT20X-HUI-SAO-P |
| GTIN (EAN) | 4050118471601 |
| Qty. | 1 items |
| 114.6 mm | |
| Depth (inches) | 4.512 inch |
| Height | 127.3 mm |
| Height (inches) | 5.012 inch |
| Width | 22.5 mm |
| Width (inches) | 0.886 inch |
| Net weight | 202 g |
| Storage temperature | -20 °C...85 °C |
| Operating temperature | -20 °C...60 °C |
| Humidity | 0...95 % (no condensation) |
| SIL PAPER | [SIL certificate](PDF/Cert_Weidmueller_070902_P0002_C005_V2R1.pdf) |
| SIL in compliance with IEC 61508 | 2 |
| REACH SVHC | Lead 7439-92-1 |
| SCIP | 2f6dd957-421a-46db-a0c2-cf1609156924 |
| Mounting position | horizontal or vertical |
| Rail | TS 35 |
| Type of mounting | DIN rail |
| Input current | 0...20 mA 4...20 mA |
| Input resistance | configurable 0…10 kΩ |
| Input resistance, current | 20 Ω + PTC 50 Ω |
| Input resistance, voltage | > 10 MΩ @ 600 mV 2 MΩ @ 28 V |
| Input voltage | configurable 0…1 V DC 0,2…1 V DC 1…5 V DC 0...(5)10 V 2…10 V DC |
| Line resistance in measuring circuit | ≤ 50 Ω |
| Potentiometer | 10 Ω…10 kΩ |
| Sensor | 2-/3-/4-wire RTD: PT10, PT20, PT50, PT100, PT250, PT300, PT400, PT500, PT1000, Ni50, Ni100, Ni120, Ni1000 Thermocouples: B, E, J, K, N, R, S, T ; in compliance with IEC 60584-1 and L, U in compliance with DIN43710 Potentiometer Resistance: 0 - 12 kΩ |
| Sensor supply | 21.4…16.5 V DC / 0…20 mA |
| Temperature input range | Configurable PT100: -200…+850 °C K: (-180…+1372 °C) L: (-200…+900 °C) N: (-180…+1300 °C) R: (-50…+1760 °C) S: (-50…+1760 °C) T: (-200…+400 °C) U: (-200…+600 °C) W3: (0…+2300 °C) W5: (0…+2300 °C) LR: (-200…+800 °C) PT200: -200…+850 °C PT1000: -200…+850 °C NI100: -60°C…+250 °C Ni120: -80 °C…+320 °C NI1000: -60°C…+250 °C B: +100…+1820 °C E: (-100…+1000 °C) J: (-100…+1200 °C) |
| Type | intrinsically safe circuit |
| Load impedance current | ≤ 600 Ω |
| Output current | 0…23 mA, configurable: 0…20 / 4…20 / 20…0 / 20…4 mA configurable downscale (3.5 mA) ⁄ upscale (23 mA) @ error |
| Output signal limit | 3.8…20.5 mA / 0…20.5 mA (dependent on range) |
| Type | active (as current source) or passive (as current sink) |
| Continuous current | ≤ 2 A AC/DC (safe area, Zone 2 area) |
| Function | Configurable switching thresholds Window function Sensor error |
| Nominal switching voltage | ≤ 250 V AC / 30 V DC (safe area) ≤ 32 V AC / 32 V DC (zone 2) |
| Power rating | ≤ 500 VA / 60 W (safe area) ≤ 16 VA / 32 W (Zone 2) |
| Type | Relay, 1 NO / NC contact |
| Alarm function | Short circuit at input Open circuit at input No supply voltage Device error |
| Continuous current | ≤ 0.5 A AC / 0.3 A DC (safe zone) ≤ 0,5 A AC / 1 A DC (zone 2) |
| Nominal switching voltage | ≤ 125 V AC / 110 V DC (safe area) ≤ 32 V AC / 32 V DC (zone 2) |
| Power rating | ≤ 62.5 VA / 32 W (safe area) ≤ 16 VA / 32 W (Zone 2) |
| Type | Status relay 1 NC (voltage-free) |
| Configuration | With FDT/DTM software Requires configuration adapter 8978580000 CBX200 USB |
| Humidity | 0...95 % (no condensation) |
| Power consumption | ≤ 2.1 W |
| Protection degree | IP20 |
| Type of connection | PUSH IN |
| Voltage supply | 19.2…31.2 V DC |
| EMC standards | DIN EN 61326 NE 21 |
| Insulation voltage | 2.6 kV (input / output) |
| Rated voltage | 300 V |
| Current I0 | 18.4 mA |
| Installation location | Device installed in safe area, zone 2 |
| Marking | II (1) G [Ex ia Ga] IIC/IIB/IIA I (M1) [Ex ia Ma] I II (1) G [Ex ia Ga] IIC II (1) D [Ex ia Da] IIIC |
| Power P0 | 40 mW |
| Voltage U0 | 8.7 V DC |
| Description of the "safe state" | analogue Output ≤ 3.6 mA or output ≥ 21 mA de-energized (relay output) |
| Device type | B |
| Diagnostic test interval | 30 s |
| Tproof | 4 a |
| Total failure rate for safe detected failures (λSD) | 0 FIT |
| Hardware fault tolerance (HFT) | 0 |
| Safety category | SIL 2 |
| Relay lifetime | 100000 times |
| Safe Failure Fraction (SFF) | 93 % |
| Mean Time To Repair (MTTR) | 24 h |
| Total failure rate for safe undetected failures (λSU) | 278 FIT |
| Total failure rate for dangerous detected failures (λDD) | 352 FIT |
| Total failure rate for dangerous undetected failures (λDU) | 43 FIT |
| Probability of outage PFH | 4.33 x 10-8 h-1 |
| Demand mode | High |
| Demand rate | 3,000 s |
| Demand response time | Signal input: <0.5 s (opto output) Temperature input: <1.1 s (opto output) |
| Average Probability of Failure on Demand (PFDavg) | 2.82 x 10-4 (Tproof = 1 year) 4.63 x 10-4 (Tproof = 2 years) 1.00 x 10-3 (Tproof = 5 years) additional data in the safety manual |
| Type of connection | PUSH IN |
| Wire connection cross section AWG, min. | AWG 26 |
| Wire connection cross section AWG, max. | AWG 14 |
| Wire cross-section, solid, min. | 0.2 mm² |
| Wire cross-section, solid, max. | 2.5 mm² |
| Wire connection cross section, finely stranded, min. | 0.2 mm² |
| Wire connection cross section, finely stranded, max. | 2.5 mm² |
| Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min. | 0.2 mm² |
| Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max. | 2.5 mm² |
| Time interval | 3 years |
| Approval/Certificate/Document of Conformity | [Certification SIL](https://mdcop.weidmueller.com/mediadelivery/asset/900_37753) [Certification DNV GL](https://mdcop.weidmueller.com/mediadelivery/asset/900_42626) [Certification ATEX](https://mdcop.weidmueller.com/mediadelivery/asset/900_97036) [Certification IECEx](https://mdcop.weidmueller.com/mediadelivery/asset/900_97154) [Certification UL](https://mdcop.weidmueller.com/mediadelivery/asset/900_103197) [Declaration of Con Check out any spare parts and components from the Weidmüller catalog!
|
