Vibration sensor VIM32PL-E1AC8-0RE-IO-1V1401
Brand: Pepperl+Fuchs
Code: VIM32PL-E1AC8-0RE-IO-1V1401
Vibration sensor with IO-Link and programmable switching output or analog current output, Series: Performance Line, Measured variable: Vibration velocity
Vibration acceleration
Temperature, Vibration acceleration: 0... 10 g rms, Interface type: IO-Link (via C/Q = Pin 4), Output type: C/Q - Pin 4 in SIO mode (switching signal of the measured variable is programmable)
Datasheet excerpt: Technical data of VIM32PL-E1AC8-0RE-IO-1V1401
| Product Description |
|---|
| Vibration sensor with IO-Link and programmable switching output or analog current output |
| General specifications | ||
|---|---|---|
| Type | Vibration sensor | |
| Measuring technology | MEMS | |
| Series | Performance Line | |
| Measured variable | Vibration velocity Vibration acceleration Temperature | |
| Measurement range | ||
| Vibration velocity | 0... 128 mm/s | |
| Vibration acceleration | 0... 10 g rms | |
| Temperature | -40... 85 °C (-40... 185 °F) | |
| Measurement accuracy | Vibration velocity: ± 0.1 mm/s (calibration point: 90% of the measuring range; 159.2 Hz) Complies with the tolerance requirements of DIN ISO 2954 for measurement range greater than 8 mm/s Vibration acceleration: ± 0.01 g (calibration point: 90% of the measuring range; 159.2 Hz) Complies with the tolerance requirements of DIN ISO 2954 | |
| Cross-sensitivity | < 5 % of the partial lateral acceleration, which acts exactly 90° to the measuring axis | |
| Resolution | Vibration velocity: 0.01 mm/s Vibration acceleration: 0.01 g | |
| Frequency range | 10... 1000 Hz | |
| Averaging time | for v-rms: 2 s for a-rms: 2 s | |
| Functional safety related parameters | ||
| MTTFd | 329 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Electrical specifications | ||
| Fusing | external fuse is required: 1 A , fast acting , 30 V DC | |
| Operating voltage | 18... 30 V DC | |
| Current consumption | max. 700 mA | |
| Power consumption | max. 21 W | |
| Time delay before availability | ≤ 1 s | |
| Surge protection | up to 2 kV | |
| Interface | ||
| Interface type | IO-Link (via C/Q = Pin 4) | |
| IO-Link revision | 1.1 | |
| Device profile | Identification and Diagnosis - I&D | |
| Process data | Input 16 Byte measurement channels: -rms value velocity - peak value acceleration - rms value acceleration - temperature per measurement channel: - measurement value 2 Byte - scaling 8 Bit - switching signals 2 Bit status data | |
| Vendor ID | 1 (0x0001) | |
| Device ID | 5308417 (0x510001) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 5 ms | |
| SIO mode support | yes | |
| Compatible master port type | Class A Class B (use 3-pole adapter or 3-wire cable) | |
| Output 1 | ||
| Output type | C/Q - Pin 4 in SIO mode (switching signal of the measured variable is programmable) | |
| Switching function | Normally open/closed (NO/NC) | |
| Operating current | ≤ 100 mA | |
| Short-circuit protection | yes | |
| Output 2 | ||
| Output type | I/Q - pin 2 (parameterizable as analog current output or switching signal) - I: analog output for the measured variable, current 4... 20 mA - Q: switching signal of the measured variable is parameterizable, PNP normally open | |
| Switching function | Normally open/closed (NO/NC) | |
| Operating current | ≤ 120 mA for switching signal | |
| Voltage drop | < 2 V | |
| Output rated operating current | 4... 20 mA at analog output | |
| Load resistor | ≤ 500 Ω at analog output | |
| Short-circuit protection | yes | |
| Standard conformity | ||
| Degree of protection | DIN EN 60529, IP66, IP67 | |
| Shock resistance | DIN EN 60068-2-27, 60 g, 6 ms | |
| Vibration resistance | DIN EN 60068-2-6, 16.5 g, 10 ... 1000 Hz | |
| Approvals and certificates | ||
| UL approval | ||
| Ordinary Location | E468231 cULus Listed, Class III Power Source and limited energy , if UL marking is marked on the product. For use in NFPA 70 Applications only. adapters providing field wiring on request | |
| Maximum permissible ambient temperature | max. 80 °C (max. 176 °F) | |
| Ambient conditions | ||
| Ambient temperature | -40... 85 °C (-40... 185 °F) | |
| Storage temperature | -40... 60 °C (-40... 140 °F) | |
| Mechanical specifications | ||
| Connection type | plug | |
| Housing material | Stainless steel 1.4305 / AISI 303 | |
| Housing length | 72.5 mm | |
| Housing diameter | 23.8 mm | |
| Degree of protection | IP66 / IP67 only in connected state | |
| Connector | ||
| Threading | M12 | |
| Number of pins | 4 | |
| Mass | approx. 100 g | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27271103 |
| ECLASS 12.0 | 27201406 |
| ECLASS 11.0 | 27201406 |
| ECLASS 10.0.1 | 27201406 |
| ECLASS 9.0 | 27201406 |
| ECLASS 8.0 | 27201406 |
| ECLASS 5.1 | 27201406 |
| ETIM 9.0 | EC004309 |
| ETIM 8.0 | EC004309 |
| ETIM 7.0 | EC002959 |
| ETIM 6.0 | EC002959 |
| ETIM 5.0 | EC001758 |
| UNSPSC 12.1 | 41114624 |
Check out any spare parts and components from the Pepperl+Fuchs catalog!
Do you want to order a Vibration sensor VIM32PL-E1AC8-0RE-IO-1V1401 with code: VIM32PL-E1AC8-0RE-IO-1V1401?
Leave your request on our website for immediate assistance!
